Published xTool settings. Not tested by Kerfbook.

XTOOL / PUBLISHED SETTINGS

xTool laser settings, each one linked to xTool’s own table.

528 published rows across 9 xTool machine/module combinations: D1 Pro 5/10/20 W, F1, Laserbox, S1.

We did not test them. Run a test card on your own sheet.

Original source on every row No uploads
MATERIAL TEST / 001SVG · MILLIMETERS
POWER × SPEEDILLUSTRATION / NOT A SETTINGS PRESETPOWER →SPEED →KERFBOOK / SAMPLE CARDYOUR SIZEYOUR MATERIAL
Example grid, not measured results.
Generate an SVG for your own sheet.
↗
Dataset coverage
xTool published tables
528 published settings9 machine/module combinations4 maker sourcesRead the source notes

01 / THE SETTINGS LIBRARY

Find a published setting.

Filter by machine, material, thickness, and operation.

Full settings library

These are the maker's published starting points. We did not test them. Run a test card on your own sheet.

Filter by machine and material
FILTER PUBLISHED SETTINGS
01 / Machine
Diode (blue)
Infrared (1064 nm)
CO2

284 published settings · showing 30

mm/min = mm/s × 60 · in/min = mm/s × 60 ÷ 25.4. Display rounded to 3 decimal places; source values stay unchanged.

Maker-published laser settings. A dash means the source did not publish a value.
Material / machineThicknessOperationPowerSpeed mm/sPassesLines/cmSource / raw
Wood
Beech Phone Stand (4pcs)xTool D1 Pro 20WWood—Bitmap engrave50%100mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 9: 50% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Beech Phone Stand (4pcs)xTool D1 Pro 20WWood—Vector engrave40%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 9: 40% / 80 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Beech Phone Stand (4pcs)xTool D1 Pro 10WWood—Bitmap engrave40%100mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 10: 40% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Beech Phone Stand (4pcs)xTool D1 Pro 10WWood—Vector engrave50%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 10: 50% / 80 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Bamboo Plant Label (60 pcs)xTool D1 Pro 20WWood—Bitmap engrave100%100mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 11: 100% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Bamboo Plant Label (60 pcs)xTool D1 Pro 20WWood—Vector engrave80%70mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 11: 80% / 70 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Bamboo Plant Label (60 pcs)xTool D1 Pro 10WWood—Bitmap engrave70%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 12: 70% / 80 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Bamboo Plant Label (60 pcs)xTool D1 Pro 10WWood—Vector engrave100%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 12: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Pine Coaster (4pcs)xTool D1 Pro 20WWood—Bitmap engrave40%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 13: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Pine Coaster (4pcs)xTool D1 Pro 20WWood—Vector engrave40%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 13: 40% / 80 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Pine Coaster (4pcs)xTool D1 Pro 10WWood—Bitmap engrave30%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 14: 30% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Pine Coaster (4pcs)xTool D1 Pro 10WWood—Vector engrave100%70mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 14: 100% / 70 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 20WWood—Bitmap engrave100%85mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 21: 100% / 85 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 20WWood—Vector engrave80%60mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 21: 80% / 60 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 10WWood—Bitmap engrave100%60mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 22: 100% / 60 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 10WWood—Vector engrave100%70mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 22: 100% / 70 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 5WWood—Bitmap engrave100%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 23: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 5WWood—Vector engrave100%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 23: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 20WWood3 mmCut100%4mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 29: 100% / 4 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 20WWood3 mmBitmap engrave60%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 29: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 20WWood3 mmFill engrave60%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 29: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 20WWood3 mmVector engrave80%60mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 29: 80% / 60 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 10WWood3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 30: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 10WWood3 mmBitmap engrave80%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 30: 80% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 10WWood3 mmFill engrave70%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 30: 70% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Fraxinus Mandshurica Plywood(6pcs)xTool D1 Pro 10WWood3 mmVector engrave50%30mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 30: 50% / 30 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

12" x 12"x 1/8" Basswood PlywoodxTool D1 Pro 20WWood3.175 mmCut100%5mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3.175 mm

Lines/cm: —

Original: Row 31: 100% / 5 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

12" x 12"x 1/8" Basswood PlywoodxTool D1 Pro 20WWood3.175 mmBitmap engrave60%100mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3.175 mm

Lines/cm: —

Original: Row 31: 60% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

12" x 12"x 1/8" Basswood PlywoodxTool D1 Pro 20WWood3.175 mmFill engrave60%100mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3.175 mm

Lines/cm: —

Original: Row 31: 60% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

12" x 12"x 1/8" Basswood PlywoodxTool D1 Pro 20WWood3.175 mmVector engrave80%60mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3.175 mm

Lines/cm: —

Original: Row 31: 80% / 60 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

02 / TEST YOUR MATERIAL

Check the range
on a scrap first.

We copied and cited the maker tables. We did not test these settings. Glue, finish, focus, and your sheet can change the result.

Build your test card
01

Match the source row.

Match the machine, material, and operation. An empty value stays empty.

02

Generate a test grid.

Make a power × speed grid. Export an SVG and a color-to-settings legend.

03

Record the result.

Run the card on your own material, following your machine’s manual. Save the result with the sheet.