Published xTool settings. Not tested by Kerfbook.

DIODE (BLUE) / 20W

xTool D1 Pro 20W
published settings.

200 published starting points for the xTool D1 Pro 20W, grouped by material category below. Keep the laser module and wattage matched to the source; another xTool module is not the same machine.

These are the maker's published starting points. We did not test them. Run a test card on your own sheet.

PUBLISHED SOURCE
xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF) ↗

xTool says these are reference values from its own tests; test your own sheet first.

Filter this machine

mm/min = mm/s × 60 · in/min = mm/s × 60 ÷ 25.4. Display rounded to 3 decimal places; source values stay unchanged.

Maker-published laser settings. A dash means the source did not publish a value.
Material / machineThicknessOperationPowerSpeed mm/sPassesLines/cmSource / raw
Acrylic
3mm Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 81: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave80%100mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 81: 80% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave80%100mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 81: 80% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 81: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 83: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 83: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 83: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 83: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Chrome Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 86: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Chrome Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave80%100mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 86: 80% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Chrome Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave80%100mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 86: 80% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Chrome Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 86: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s2—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 88: 100% / 3 mm/s / 2 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave100%100mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 88: 100% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave100%100mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 88: 100% / 100 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Yellow Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 88: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Orange Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 90: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Orange Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 90: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Orange Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 90: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Orange Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 90: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s2—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 92: 100% / 3 mm/s / 2 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 92: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 92: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 92: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Green Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 95: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Green Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave60%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 95: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Green Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmFill engrave60%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 95: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Green Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmVector engrave30%40mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 95: 30% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Deep Green Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmCut100%3mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 97: 100% / 3 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Deep Green Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 20WAcrylic3 mmBitmap engrave60%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 97: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

— = not published by the source. Open “Raw + notes” on a row to see its original text and any extra parameters. How we handle source data.