Published xTool settings. Not tested by Kerfbook.

DIODE (BLUE) / 5W

xTool D1 Pro 5W
published settings.

19 published starting points for the xTool D1 Pro 5W, grouped by material category below. Keep the laser module and wattage matched to the source; another xTool module is not the same machine.

These are the maker's published starting points. We did not test them. Run a test card on your own sheet.

PUBLISHED SOURCE
xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF) ↗

xTool says these are reference values from its own tests; test your own sheet first.

Filter this machine

mm/min = mm/s × 60 · in/min = mm/s × 60 ÷ 25.4. Display rounded to 3 decimal places; source values stay unchanged.

Maker-published laser settings. A dash means the source did not publish a value.
Material / machineThicknessOperationPowerSpeed mm/sPassesLines/cmSource / raw
Acrylic
3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 5WAcrylic3 mmCut100%1mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 85: 100% / 1 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 5WAcrylic3 mmBitmap engrave100%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 85: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Dark Red Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 5WAcrylic3 mmFill engrave100%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 85: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 5WAcrylic3 mmCut100%1mm/s3—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 94: 100% / 1 mm/s / 3 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 5WAcrylic3 mmBitmap engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 94: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Brown Acrylic Sheet(Opaque,Glossy)xTool D1 Pro 5WAcrylic3 mmFill engrave40%50mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: Row 94: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Metal
Metal Business Cards (60pcs) BluexTool D1 Pro 5WMetal—Bitmap engrave60%50mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: Row 3: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Metal Business Cards (60pcs) BluexTool D1 Pro 5WMetal—Vector engrave100%50mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: Row 3: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Silver Stainless Steel Tag 10pcsxTool D1 Pro 5WMetal—Bitmap engrave100%3mm/s2—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: Row 6: 100% / 3 mm/s / 2 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Other
Cork Desk PadxTool D1 Pro 5WOther—Bitmap engrave100%40mm/s1—xTool source
Raw + notes

Category: Other

Thickness: —

Lines/cm: —

Original: Row 26: 100% / 40 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Cork Desk PadxTool D1 Pro 5WOther—Vector engrave100%50mm/s1—xTool source
Raw + notes

Category: Other

Thickness: —

Lines/cm: —

Original: Row 26: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Wood
Round Wooden Keychain 10 pcsxTool D1 Pro 5WWood—Bitmap engrave100%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 23: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

Round Wooden Keychain 10 pcsxTool D1 Pro 5WWood—Vector engrave100%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: —

Lines/cm: —

Original: Row 23: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Basswood plywood 30*30 6pcsxTool D1 Pro 5WWood3 mmCut100%2mm/s2—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 55: 100% / 2 mm/s / 2 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Basswood plywood 30*30 6pcsxTool D1 Pro 5WWood3 mmBitmap engrave100%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 55: 100% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Cherry wood plywood 30*30 6pcsxTool D1 Pro 5WWood3 mmCut100%2mm/s2—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 58: 100% / 2 mm/s / 2 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Cherry wood plywood 30*30 6pcsxTool D1 Pro 5WWood3 mmBitmap engrave60%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 58: 60% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Walnut plywood 30*30 6pcsxTool D1 Pro 5WWood3 mmCut100%2mm/s2—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 61: 100% / 2 mm/s / 2 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

3mm Walnut plywood 30*30 6pcsxTool D1 Pro 5WWood3 mmBitmap engrave40%50mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 61: 40% / 50 mm/s / 1 pass(es)

Extra: —

xTool: D1 Pro Engraving & Cutting Parameters for Reference (PDF)

xTool says these are reference values from its own tests; test your own sheet first.

— = not published by the source. Open “Raw + notes” on a row to see its original text and any extra parameters. How we handle source data.