Published xTool settings. Not tested by Kerfbook.

CO2 / 40W

xTool Laserbox 40W
published settings.

64 published starting points for the xTool Laserbox 40W, grouped by material category below. Keep the laser module and wattage matched to the source; another xTool module is not the same machine.

These are the maker's published starting points. We did not test them. Run a test card on your own sheet.

PUBLISHED SOURCE
xTool: Recommended Material Processing Parameters for Laserbox ↗

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

Filter this machine

mm/min = mm/s × 60 · in/min = mm/s × 60 ÷ 25.4. Display rounded to 3 decimal places; source values stay unchanged.

Maker-published laser settings. A dash means the source did not publish a value.
Material / machineThicknessOperationPowerSpeed mm/sPassesLines/cmSource / raw
Paper & card
2mm Corrugated PaperxTool Laserbox 40WPaper & card2 mmCut90%40mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: 2 mm

Lines/cm: —

Original: Row 1

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

2mm Corrugated PaperxTool Laserbox 40WPaper & card2 mmVector engrave5%80mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: 2 mm

Lines/cm: —

Original: Row 2

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

2mm Corrugated PaperxTool Laserbox 40WPaper & card2 mmFill engrave10%130mm/s190xTool source
Raw + notes

Category: Paper & card

Thickness: 2 mm

Lines/cm: 90

Original: Row 3

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

2mm Corrugated PaperxTool Laserbox 40WPaper & card2 mmBitmap engrave3%80mm/s1100xTool source
Raw + notes

Category: Paper & card

Thickness: 2 mm

Lines/cm: 100

Original: Row 4

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3.5mm Corrugated PaperxTool Laserbox 40WPaper & card3.5 mmCut100%27mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: 3.5 mm

Lines/cm: —

Original: Row 5

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3.5mm Corrugated PaperxTool Laserbox 40WPaper & card3.5 mmVector engrave5%80mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: 3.5 mm

Lines/cm: —

Original: Row 6

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3.5mm Corrugated PaperxTool Laserbox 40WPaper & card3.5 mmFill engrave10%130mm/s190xTool source
Raw + notes

Category: Paper & card

Thickness: 3.5 mm

Lines/cm: 90

Original: Row 7

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3.5mm Corrugated PaperxTool Laserbox 40WPaper & card3.5 mmBitmap engrave3%80mm/s1100xTool source
Raw + notes

Category: Paper & card

Thickness: 3.5 mm

Lines/cm: 100

Original: Row 8

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

Kraft PaperxTool Laserbox 40WPaper & card—Cut100%25mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: —

Original: Row 61

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

Kraft PaperxTool Laserbox 40WPaper & card—Vector engrave1%80mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: —

Original: Row 62

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

Kraft PaperxTool Laserbox 40WPaper & card—Fill engrave5%130mm/s190xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: 90

Original: Row 63

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

Kraft PaperxTool Laserbox 40WPaper & card—Bitmap engrave3%100mm/s1100xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: 100

Original: Row 64

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

Wood
3mm Basswood PlywoodxTool Laserbox 40WWood3 mmCut95%20mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 9

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Basswood PlywoodxTool Laserbox 40WWood3 mmVector engrave20%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 10

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Basswood PlywoodxTool Laserbox 40WWood3 mmFill engrave15%130mm/s190xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: 90

Original: Row 11

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Basswood PlywoodxTool Laserbox 40WWood3 mmBitmap engrave3%80mm/s1100xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: 100

Original: Row 12

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Basswood PlywoodxTool Laserbox 40WWood5 mmCut100%6mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: —

Original: Row 13

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Basswood PlywoodxTool Laserbox 40WWood5 mmVector engrave25%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: —

Original: Row 14

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Basswood PlywoodxTool Laserbox 40WWood5 mmFill engrave15%130mm/s190xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: 90

Original: Row 15

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Basswood PlywoodxTool Laserbox 40WWood5 mmBitmap engrave3%80mm/s1100xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: 100

Original: Row 16

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Black Walnut PlywoodxTool Laserbox 40WWood3 mmCut95%12mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 17

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Black Walnut PlywoodxTool Laserbox 40WWood3 mmVector engrave30%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 18

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Black Walnut PlywoodxTool Laserbox 40WWood3 mmFill engrave20%130mm/s190xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: 90

Original: Row 19

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Black Walnut PlywoodxTool Laserbox 40WWood3 mmBitmap engrave3%80mm/s1100xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: 100

Original: Row 20

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Black Walnut PlywoodxTool Laserbox 40WWood5 mmCut100%12mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: —

Original: Row 21

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Black Walnut PlywoodxTool Laserbox 40WWood5 mmVector engrave30%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: —

Original: Row 22

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Black Walnut PlywoodxTool Laserbox 40WWood5 mmFill engrave20%130mm/s190xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: 90

Original: Row 23

Extra: Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

5mm Black Walnut PlywoodxTool Laserbox 40WWood5 mmBitmap engrave3%80mm/s1100xTool source
Raw + notes

Category: Wood

Thickness: 5 mm

Lines/cm: 100

Original: Row 24

Extra: Bitmap mode Grayscale, Bi-directional

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Cherry PlywoodxTool Laserbox 40WWood3 mmCut95%14mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 25

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

3mm Cherry PlywoodxTool Laserbox 40WWood3 mmVector engrave25%80mm/s1—xTool source
Raw + notes

Category: Wood

Thickness: 3 mm

Lines/cm: —

Original: Row 26

Extra: —

xTool: Recommended Material Processing Parameters for Laserbox

Updated by xTool on 2023-09-19. Laboratory conditions, for reference only.

— = not published by the source. Open “Raw + notes” on a row to see its original text and any extra parameters. How we handle source data.