Published xTool settings. Not tested by Kerfbook.

INFRARED (1064 NM) / 2W

xTool F1 (2W infrared)
published settings.

30 published starting points for the xTool F1 (2W infrared), grouped by material category below. Keep the laser module and wattage matched to the source; another xTool module is not the same machine.

These are the maker's published starting points. We did not test them. Run a test card on your own sheet.

PUBLISHED SOURCE
xTool: Processing Parameter Settings Recommended for Common Materials (F1) ↗

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Filter this machine

mm/min = mm/s × 60 · in/min = mm/s × 60 ÷ 25.4. Display rounded to 3 decimal places; source values stay unchanged.

Maker-published laser settings. A dash means the source did not publish a value.
Material / machineThicknessOperationPowerSpeed mm/sPassesLines/cmSource / raw
Acrylic
3mm Black AcrylicxTool F1 (2W infrared)Acrylic3 mmScore80%60mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: 80%-60mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

3mm Black AcrylicxTool F1 (2W infrared)Acrylic3 mmVector engrave90%200mm/s1200xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: 200

Original: 90%-200mm/s-200 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

3mm Black AcrylicxTool F1 (2W infrared)Acrylic3 mmBitmap engrave85%—mm/s1—xTool source
Raw + notes

Category: Acrylic

Thickness: 3 mm

Lines/cm: —

Original: 85%-200μs-550DPI-Jarvis-Invert-1

Extra: Dot duration 200 μs, 550 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Metal
BrassxTool F1 (2W infrared)Metal—Score80%300mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 80%-300mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

BrassxTool F1 (2W infrared)Metal—Vector engrave100%300mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 100%-300mm/s-200 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

BrassxTool F1 (2W infrared)Metal—Bitmap engrave80%—mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 80%-200μs-550DPI-Jarvis-Invert-1

Extra: Dot duration 200 μs, 550 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Red CopperxTool F1 (2W infrared)Metal—Score100%10mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 100%-10mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Red CopperxTool F1 (2W infrared)Metal—Vector engrave100%3mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 100%-3mm/s-200 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Aluminum SheetxTool F1 (2W infrared)Metal—Score90%350mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 90%-350mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Aluminum SheetxTool F1 (2W infrared)Metal—Vector engrave100%600mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 100%-600mm/s-200 line per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Aluminum SheetxTool F1 (2W infrared)Metal—Bitmap engrave60%—mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 60%-200μs-550DPI-Jarvis-Invert-1

Extra: Dot duration 200 μs, 550 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Gilded MaterialxTool F1 (2W infrared)Metal—Score100%10mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 100%-10mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Gilded MaterialxTool F1 (2W infrared)Metal—Vector engrave100%5mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 100%-5mm/s-200 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

SilverxTool F1 (2W infrared)Metal—Score100%10mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 100%-10mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

SilverxTool F1 (2W infrared)Metal—Vector engrave100%5mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 100%-5mm/s-200 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Black Metal Name CardxTool F1 (2W infrared)Metal—Score90%650mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 90%-650mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Black Metal Name CardxTool F1 (2W infrared)Metal—Vector engrave100%650mm/s1220xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 220

Original: 100%-650mm/s-220 lines per cm -1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Black Metal Name CardxTool F1 (2W infrared)Metal—Bitmap engrave60%—mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 60%-150μs-750DPI-Jarvis-Invert-1

Extra: Dot duration 150 μs, 750 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Black Alumina SheetxTool F1 (2W infrared)Metal—Score80%800mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 80%-800mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Black Alumina SheetxTool F1 (2W infrared)Metal—Vector engrave90%500mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 90%-500mm/s-200 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Black Alumina SheetxTool F1 (2W infrared)Metal—Bitmap engrave70%—mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 70%-150μs-500DPI-Jarvis-Invert-1

Extra: Dot duration 150 μs, 500 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Stainless SteelxTool F1 (2W infrared)Metal—Score80%25mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 80%-25mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Stainless SteelxTool F1 (2W infrared)Metal—Vector engrave50%550mm/s1200xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: 200

Original: 50%-550mm/s-200line per cm -1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Stainless SteelxTool F1 (2W infrared)Metal—Bitmap engrave60%—mm/s1—xTool source
Raw + notes

Category: Metal

Thickness: —

Lines/cm: —

Original: 60%-150μs-450DPI-Jarvis-Invert-1

Extra: Dot duration 150 μs, 450 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Paper & card
Art Scratch PaperxTool F1 (2W infrared)Paper & card—Score90%1,650mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: —

Original: 90%-1650mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Art Scratch PaperxTool F1 (2W infrared)Paper & card—Vector engrave60%1,700mm/s1220xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: 220

Original: 60%-1700mm/s-220 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Art Scratch PaperxTool F1 (2W infrared)Paper & card—Bitmap engrave50%—mm/s1—xTool source
Raw + notes

Category: Paper & card

Thickness: —

Lines/cm: —

Original: 50%-200μs-400DPI-Jarvis-Invert-1

Extra: Dot duration 200 μs, 400 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Stone
Rock CoasterxTool F1 (2W infrared)Stone—Score100%50mm/s1—xTool source
Raw + notes

Category: Stone

Thickness: —

Lines/cm: —

Original: 100%-50mm/s-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Rock CoasterxTool F1 (2W infrared)Stone—Vector engrave100%100mm/s1240xTool source
Raw + notes

Category: Stone

Thickness: —

Lines/cm: 240

Original: 100%-100mm/s-240 lines per cm-1

Extra: —

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

Rock CoasterxTool F1 (2W infrared)Stone—Bitmap engrave90%—mm/s1—xTool source
Raw + notes

Category: Stone

Thickness: —

Lines/cm: —

Original: 90%-150μs-450DPI-Jarvis-Invert-1

Extra: Dot duration 150 μs, 450 DPI, Jarvis Invert

xTool: Processing Parameter Settings Recommended for Common Materials (F1)

Updated by xTool on 2023-08-03. Based on xTool laboratory tests.

— = not published by the source. Open “Raw + notes” on a row to see its original text and any extra parameters. How we handle source data.